Manual instruction PINOPRIDE Solar Powered Charger

PACKAGING INCLUDE

  1. 1 pices solar charger power bank
  2. 1 piece lether cord
  3. 1 piece USB cable for charging
  4. 1 piece instructions for use
  5. 1 piece Insert Card for Customer

 

 

 

SPECIFICATION

  1. PINOPRIDE Solar Charger Power Bank
  2. Model: PINOMD-T10
  3. Battery Type: 18650
  4. Capacity: 15000mAh
  5. Input: 5V/1,5A
  6. Output: 5V/3X2.1A
  7. Daylight lamp/Warning lamp: 2.1 W
  8. Solar Panel: 1.3-7W/250mA
  9. Product Dimension: 150x74x26 mm
  10. Pcking dimension: 170x95x26 mm
  11. Product Weight: 400 g
  12. AC in charging time: about 10-12 hours
  13. DC out charging time: about 5-7 time, depends on type of user

Remark:              Products are manufacured with CE FCC RoHS MSDS certification.

 

MANUAL INSTRUCTION

Instruction Introduce

Pull down PVC transparent cover protection from sunglass panel!

Multifuction digital movable charger. Using the efficient boost converter and battery protective IC. It’s build in intelligent identification chips are able to identify different kinds of digital products, the voltage and electric current. Super drop resistance and dustproof. Used ABC and electroplating material with anti-skid lines. Build-in lithium polymer battery which charges via a powerful between 1.1-1.7W monocrystalline solar panel. Reaching available charge. It with build-in high capacity battery, small appearance, wide scope of application, longevity life, high cost performance. Suitable for charging Iphones, Ipads, all Android’s as Samsung, LG, HTC, …. Phones and Tablets, GPS devices, Cameras, Bluetooth and etc. at any time.

INPUT CHARGING TO THE SOLAR CHARGER POWER BANK

  1. Plug USB Cord Cable which is including in packaging on DC12/24V or AC 110/220V.
  2. Use USB to DC or AC adapter. Is not include! Use your phone USB
  3. adapter or other.
  4. Push ON button
  5. If you see 1 – 4 blue led lights on right site is conecting OK.
  6. If NOT, please see following:

Note:

Please check if the USB and the cable connect correctly when charging. If charge is not efficient, it may because the build it IC start the short Circuit protection system when connection is not right, it can be used properly when you adjust it and then charge again.

 

INPUT SOLAR MOBILE POWER CHARGING

  1. Push ON button
  2. If you see 1 green led lights on right site, it is connecting to solar charging.

Note: If daylight is not enough strong GREEN led light is not ON!

 

RECOMMENDED EMERGENCY Note:

The energy transformation from solar to electricity is rather slow, Solar Charging is only recommended for EMERGENCY use,please DO NOT take it as primary power resource.

Solar Panel charged output are 1.3-7W/250mA

Solar Charging effect will be subject to sunlight intensity and local weather.

For daily use, please use provided to charge the power bank via wall outlet!!!

For your safety, please DO NOT leave the power bank charging in car in case of high temperature and avoid crashing, which may cause potential hazards. High temperature in car may damage it.
In order to fully activate the battery, please charge it via outlet or computer for min 10 hours at least at the first uses.

OUTPUT DIGITAL MOBILE DEVICES POWER CHARGING

  1. Plug USB phone cable which is NOT including in packaging in to
  2. USB 2.0 to PINOPRIDE Solar Charger Power Bank
  3. Connect the cable connector to your Digital Mobile Suitable Devices for charging as Iphones, Ipads, all Android’s as Samsung, LG, HTC, …. Phones and Tablets, GPS devices, Cameras, Bluetooth and etc.
  4. Push ON button
  5. If you see 1 – 4 blue led lights on right site is connecting OK.
  6. If NOT, please see following:

Note:

Please check if the USB and the cable connect correctly when charging. If charge is not efficient, it may because the build it IC start the short Circuit protection system when connection is not right, it can be used properly when you adjust it and then charge again

You can power up three mobile devices simultanion!

Facebook
Twitter
Pinterest